• LOW & MID FREQUENCY
• COAXIALS
• COMPRESSION DRIVERS
• COMPRESSION DRIVERS WITH WAVE GUIDES
• AMT DRIVERS
• COMPRESSION TWEETERS
• DOME TWEETERS
• FULL RANGE
• HORNS
• PASSIVE FILTERS
• SHAKERS

• LIGHT CATALOGUE
• FAVORITES
• DISCONTINUED

MODEL		-- DIAMETER (in)	-- POWER (W AES)	SEN. (dB 2.83V-1m)	FREQ. RANGE (Hz)	-- COIL DIAM. (in)	Fs (Hz)	Qts	Vas (l)	Xmax (mm)	NET WEIGHT (kg)	MAGNET	PDF	Fav.
		<···>	<···>	<···>	<···>	<···>	<···>	<···>	<···>	<···>	<···>	<···>
5G40Nd/N		5	100	92	150-17000	1.5	140	0.45	1.45	3	1.3	Nd
5P200Fe		5	150	92	70-10000	1.5	72	0.33	5.69	5.5	2.19	Ferr
5P200Nd		5	150	92	70-10000	1.5	78	0.3	4.5	5.7	1.24	Nd
6G40Fe		6.5	170	94.3	70-9000	2	102	0.4	5.04	3.1	3.02	Ferr
6G40Nd		6.5	170	95	70-9000	2	88	0.33	7.2	1	1.7	Nd
6MCF200Nd		6.5	200	97	400-12000	2	410	0.64	0.25	2.5	2.3	Nd
6MI100		6.5	250	94	100-8000	2	128	0.51	3.07	3	2.2	Ferr
6P200Nd		6.5	200	92	60-9000	2	56	0.29	11.9	5.5	1.9	Nd
6P200Fe		6.5	200	93	55-9000	2	58	0.26	11.1	5.5	3.1	Ferr
8G40		8	250	95	65-6000	2.5	70	0.36	17	4.5	3.3	Ferr
8LW30		8	250	95	65-6000	2.5	70	0.37	16	4.5	2.35	Nd
8MC300Nd		8	300	96	80-4000	2	76	0.28	11.6	6	1.9	Nd
8MC500Nd	New!	8	500	98	80-6000	2.5	75	0.19	12.2	5	2.8	Nd
8MI100		8	250	98	150-7000	2	90	0.56	13	1	3.1	Ferr
8P300Fe/N		8	300	94	55-8000	2.5	53	0.31	24.8	6	4	Ferr
SM-108		8	150	95	70-6000	2	71	0.32	14.4	6	3.1	Ferr
8WR300		8	300	95	65-4000	2	62	0.24	17.7	6	3.3	Ferr
8WRS300		8	300	95	70-4000	2	68	0.27	12.5	6	3.25	Ferr
10G40		10	400	95	45-4000	3	45	0.3	49	7	5.7	Ferr
10LW30/N		10	450	95	55-4000	3	55	0.29	28	7	3.75	Nd
10MC500		10	500	97	70-5000	2.5	60	0.28	26	8	5.7	Ferr
10MC700Nd	New!	10	700	97	60-4000	3	56	0.21	25.5	7	3.6	Nd
10MCF400Nd		10	400	102	300-5000	4	270	0.45	1.8	3.5	6.2	Nd
10MCS500		10	500	96	70-5000	2.5	70	0.37	18.8	8	5.7	Ferr
10MI100		10	350	98	70-4000	3	50	0.21	54	4.5	7.1	Ferr
SM-110/N		10	200	95	45-6500	2	43	0.35	65	4	3.5	Ferr
10WR300		10	300	95	55-5000	2	47	0.32	50.9	6	3.5	Ferr
10WRS300		10	300	94.5	55-5000	2	52	0.38	39.3	6	3.5	Ferr
12G40		12	500	97	35-4000	3	44	0.3	81	5	7.1	Ferr
12LW30/N		12	450	96	40-4000	3	42	0.27	84	7	3.9	Nd
12LX60V2		12	700	96	35-2000	4	49	0.38	43	9	9.7	Ferr
12MC500		12	500	98	65-5000	2.5	57	0.38	54.9	8	5.86	Ferr
12MC700Nd	New!	12	700	99	60-4000	3	58	0.24	42	7	3.7	Nd
12MCS500		12	500	97	65-5000	2.5	62	0.42	44	8	6	Ferr
12MI100		12	450	100	40-4000	3	58	0.22	64	2	7.2	Ferr
12P1000Nd		12	900	96	30-2500	4	47	0.26	49	8	5.4	Nd
12P80Fe/V2		12	700	100	50-4000	4	51	0.185	60.5	7.5	11.5	Ferr
12P80Nd/V2		12	700	101	45-4000	4	45	0.15	77.1	7.5	5.6	Nd
SM-212		12	350	97	45-4000	2.5	43	0.38	103	8.25	4.6	Ferr
SM-112/N		12	400	97	40-4000	3	40	0.3	117.3	7.25	5.65	Ferr
12SW1300Nd		12	1200	96	25-1800	4	45	0.26	45	10	7.2	Nd
12WR400		12	400	97	45-5000	3	42	0.28	91,1	6.3	5.5	Ferr
12WRS400		12	400	96.5	45-5000	3	44	0.31	77.9	6.3	5.5	Ferr
15G40		15	700	97	40-1500	4	38	0.32	128	9.5	10.4	Ferr
15LEX1600Nd	New!	15	1600	96	40-1500	4	41	0.36	91	14.5	8.8	Nd
15LW30		15	500	98	35-4000	3	34	0.33	251	7	4.5	Nd
15LX60V2		15	700	98	30-1500	4	42	0.44	105.53	9	10.2	Ferr
15MC500		15	500	98	50-4000	2.5	46	0.46	131.5	8	6.2	Ferr
15MC700		15	700	98	45-4000	3	41	0.35	153	9.8	7.5	Ferr
15MC700Nd	New!	15	700	100	50-4000	3	49	0.31	105	7	4.2	Nd
15MCS500		15	500	97.5	50-4000	2.5	46	0.48	133.5	8	6.2	Ferr
15MI100		15	450	100	40-5000	3	37	0.29	264	4.5	7.8	Ferr
15P1000Fe V2		15	1000	98	45-2000	4	45	0.3	80.7	8	13.1	Ferr
15P80Fe/N		15	800	101	30-4000	4	32	0.18	305	7.5	12.5	Ferr
15P80Nd		15	800	100	30-4000	4	33	0.178	250	7.5	6	Nd
SM-115N		15	400	98	35-3000	3	35	0.38	267	7.25	6.5	Ferr
15SW1300Nd		15	1300	97	25-1800	4	44	0.36	89.6	10	7.7	Nd
15WR400		15	400	99	40-4000	3	36	0.3	224	6.3	6.1	Ferr
15WRS400		15	400	98	40-4000	3	35	0.33	233	6.3	6.25	Ferr
18G550		18	900	97	35-1500	4.5	33	0.4	290	10	12.60	Ferr
18LEX1600Nd		18	1600	96	35-1000	4	33	0.43	231	14.5	9.5	Nd
18LX60V2		18	700	98	25-1000	4	35	0.48	236.52	9	11.7	Ferr
18P1000Fe V2		18	1200	98	30-2000	4	33	0.32	230	8	13.8	Ferr
18P1200Nd/N		18	1200	98	25-2000	4	37	0.34	198	9.5	8.5	Nd
18PW1400Fe		18	1400	98	25-1800	4	32	0.27	228.9	10	16.9	Ferr
18PWB1000Fe		18	1000	96	30-2000	4	27	0.38	317	12.5	13.6	Ferr
18WRS600		18	600	98	35-1000	3	32	0.4	372	8.5	8.7	Ferr
21LEX1600Nd	New!	21	1600	99.5	30-1000	4	30	0.27	394	13	11.8	Nd
21PW1400Fe		21	1400	98.5	25-1800	4	30	0.34	401.5	10	19.9	Ferr
5MP60/N		5	50 W RMS	88	50-12000	1	63	0.46	5.77	5.5	1.2	Ferr
6B30/P		6.5	50 W RMS	90	55-8000	1	56	0.50	15.6	5.5	1.25	Ferr
8BR40/N		8	50 W RMS	91	30-6000	1	30	0.39	89.1	6.7	1.35	Ferr
10BR60/V2		10	100 W RMS	90.6	30-5000	2	31	0.47	108.2	6.5	2.87	Ferr
12BR70		12	125 W RMS	93	25-4000	2	31	0.50	142	8	3.6	Ferr
6CMV2	New!	6.5	220	94	95-8000	1.5	92	0.38	5.2	5.7	2.2	Ferr
8BFR		8	50 W RMS	90	30-6000	1	52	0.92	29.6	5.7	1.17	Ferr
8CMV2	New!	8	250	94	80-8000	1.5	75	0.52	14.6	5.7	2.4	Ferr
10CMV2	New!	10	250	95	60-5000	1.5	55	0.42	40.3	6.5	3.1	Ferr
12CMV2	New!	12	320	96	50-6000	2.5	45	0.41	89	7	4.6	Ferr
15CMV2	New!	15	350	97	40-4000	3	37	0.39	188	7	6	Ferr

6G40Fe GRAPH TECHNICAL SPECIFICATIONS Nominal diameter 165 mm 6.5 in Nominal impedance 8 Ohm Minimum impedance 7.9 ohm Power capacity 170 W AES Program power 340 W Sensitivity 94.3 dB 1 W @ 1m @ 2Π Frequency range 70-9000 Hz Recommended enclosure volume 10 / 30 l 0.35 / 1.06 ft.³ Voice coil diameter 51.7 mm 2 in BL factor 11 N /A Moving mass 0.013 kg Winding length 9.2 mm Air gap height 7 mm Xdamage pp 37.8 mm THIELE SMALL PARAMETERS Fs 102 Hz Re 6 ohm Qms 9.25 Qes 0.42 Qts 0.4 Vas 5.04 l Cms 184 µm / N Rms 0.91 kg / s Efficiency % 1.24 Sd 0.014 m² Xmax 3.1 mm Vd 14 cm³ Le @1 kHz 0.5 mH CONSTRUCTIVE DETAILS Net weight 3.02 kg 6.66 lb Total weight 3.12 kg 6.88 lb Magnet Ferrite TECHNOLOGIES MMSS SHARE × HELICEX This speaker has Helicex technology, which gives: - Higher power handling capacity. The thermal limit is effectively reduced, allowing the voice coil to work 80ºC below comparing to our previous thermal circuit. - Reduced power compression losses, which allows to keep the final SPL (Sound Pressure Level) in more constant values within a working period. - More stable and linear behaviour of the moving assembly in long excursions thanks to the new system design, reducing offset issues commonly related to asymmetries in non-linear components (mainly Bl(x), L(x) and Kms(x)). - Dynamic response. The efficiency of the HELICEX® system allows to use 5” or 4” voice coil diameter (depending on model), which means lower Mms values and better control of the moving assembly compared to other systems and comparable products available nowadays, as well as lower overall weights of the speaker because of an optimized dimensioning of the mechanical assembly. × PM4 This speaker has PM4 technology The new PM4 diaphragm, incorporates a new high tech polymer never used in audio before. Delivers a stronger joint between the dome and the former of the voice coil and so a better behaviour with high power handling and long periods of working. In the subjective field, which is also a relevant part in the Beyma development process, in our opinion it brings a more natural sound when comparing it with other polyesters. × MMSS MMSS Technology (Mechanical Mirror Suspension System) Ideally the moving assembly behaviour must be the same in positive and negative excursions. To provide this attribute correctly depends on the magnetic circuit design but also on the suspension system characteristics. Our tool for achieving a symmetric movement pattern is the MMSS Technology, which provides to our engineers a complete set of components with their parameters in long excursion terms. × MALT CROSS In Beyma we face the problem of heat dissipation with a clear goal in mind: the speaker must deliver the best performance in the system in a consistent and reliable way, maximizing the total SPL and keeping it stable. It is well known how the overall SPL of a system suffers a drop after some time working due to the power compression effect in the speakers. It is also known the bigger the voice coil diameter the lower the power compression and the higher the power capacity, but this also means bigger motor structures to obtain high sensitivity from the transducer. The latest cooling technology that we deliver to the Professional Audio market through our new speakers, bring together several solutions to meet our goal; in one side allows the woofer to handle bigger rates of power with a given coil diameter, so we can think in smaller coil designs with smaller motor structure, reducing the weight but increasing the sensitivity and also keeping an adequate power handling figure for a target application. Products like the 18PW1400Fe, 21PW1400Fe or the unique 12MC500 are designed following that concept; models that even with a ceramic magnet structure, feature high sensitivity, an increased power capacity and performance comparable to bigger coil designs with neodymium motor structures. × X-BOW The increase of temperature in a pleated diaphragm strains every fold, limiting the electrical power it can handle.    The target of Xbow Technology is to open as much as possible the constraint in the diaphragm, allowing it to manage higher temperature rates and so increasing the limit of the power it can handle.

News